Dryer · Whirlpool
Whirlpool Dryer Won't Start: Start Button, Control Lock and Power
Whirlpool dryer won't start? Whirlpool says to hold Start for 2 to 5 seconds, not tap it. Then check Control Lock, the door latch, the cycle setting and power.
Last verified November 16, 2026
Start here
Before you begin, make sure the dryer is plugged in and set up normally —start was tapped instead of held. whirlpool says start, push to start or hold to start must be held for two to five seconds.
Start troubleshootingSafety notice
Unplug the dryer before checking the power cord's terminal screws at the back of the dryer.
View detailed safety tipsMost Likely Causes
Based on common issues for this problem.
- 1Start was tapped instead of held. Whirlpool says Start, Push to Start or Hold to Start must be held for two to five seconds
- 2Control Lock is on, so the controls ignore every touch
- 3The door looks shut but isn't latched (some models have an upper and a lower latch, and both must be secure)
- 4The cycle knob is on Wrinkle Shield or Wrinkle Reduction, which won't start the dryer on some models
- 5No power: a tripped breaker or blown fuse (electric dryers use two), or an incorrectly installed power cord
Also described as: “Whirlpool dryer won't turn on”, “Whirlpool dryer start button not working”, “Whirlpool dryer has power but won't start”, “Whirlpool dryer not tumbling”
Where to Start
First question: do the drum light or the controls light up? If they do, the dryer has power, and Whirlpool's checks are the Start button, Control Lock, the door latch and the cycle setting, in that order. If nothing lights up, go straight to the breaker, fuse and power cord checks.
Do the drum light or the controls light up?
Yes, it has power
Hold Start for 2 to 5 seconds, turn off Control Lock, make sure the door is latched and the cycle isn't set to Wrinkle Shield.
No, nothing lights up
Check the household breakers or fuses (two on an electric dryer) and that the power cord is installed correctly.
Steps and error codes sourced from Whirlpool's official Product Help documentation (dryer not starting, controls not working, no power, not tumbling and dryer error code pages). Reviewed November 16, 2026.
Safety Notes
- Unplug the dryer before checking the power cord's terminal screws at the back of the dryer.
- If a breaker keeps tripping or a fuse keeps blowing, stop resetting it and call an electrician. Whirlpool gives the same advice.
- Electric dryers need a 240-volt supply. If you don't have 240 volts at the outlet, the dryer won't operate correctly — that's a job for a qualified electrician, not a dryer repair.
If your Whirlpool dryer won’t start, try the simplest fix first: hold the Start button for two to five seconds instead of tapping it. Whirlpool’s own documentation says a quick tap may not allow enough time to engage the motor. If that doesn’t work, Whirlpool’s checklist is short: Control Lock, the door latch, the cycle setting, and then power.
This page covers what’s specific to Whirlpool. For general part checks (door switch, thermal fuse, start switch and drive belt), see the main dryer won’t start guide. More Whirlpool guides are on the Whirlpool brand page.
Diagnostic Steps
Your progress
0 of 5 steps checked
Press and hold Start for two to five seconds
- What to look for
- Whether you tapped Start or held it.
- What it indicates
- Whirlpool says the Start, Push to Start or Hold to Start button should be pressed and held for two to five seconds. Just tapping it may not allow enough time to engage the motor, so the dryer looks dead even though nothing is wrong.
- What to do
- Hold Start firmly for two to five seconds. On touch-control models, use your fingertip, not your fingernail. Moisture stops the touch panel responding, the same way it does on a phone screen, so dry your hands and wipe the panel with a clean, dry cloth first.
- If nothing changes
- Check whether Control Lock is on.
Turn off Control Lock
- What to look for
- A lit Control Lock or Controls Locked light.
- What it indicates
- Control Lock (sometimes called child lock) locks out the electronic control, so the controls won't respond to any touch and the dryer can't be started.
- What to do
- Hold the Control Lock button for three seconds. On models without a separate Control Lock button, Whirlpool says holding the Cycle Signal button for three seconds turns it off on most models. If neither works, your owner's manual shows the button for your model.
- If nothing changes
- If the light is off and the controls respond but the dryer still won't start, check the door latch.
Make sure the door is latched
- What to look for
- A door that looks shut but isn't latched, and anything in the way of the latch.
- What it indicates
- The dryer won't run unless the door is latched. Some Whirlpool models have an upper and a lower latch, and both must be secure. Clothing caught in the door, or packing or shipping material left on a new dryer, can stop it closing completely.
- What to do
- Push on the door to engage the latch or latches. Make sure all the clothing is inside the drum and nothing is blocking the latch. On a new dryer, check that all packing and shipping material has been removed.
- If nothing changes
- Check which cycle the knob is set to.
Check the cycle setting
- What to look for
- Where the Cycle Control knob is pointing.
- What it indicates
- On some models, the knob must be on an Automatic Dry, AccuDry or Time Dry cycle. The dryer won't start if it's set to the Wrinkle Shield option (Wrinkle Reduction on some models).
- What to do
- Turn the knob to an Automatic Dry or Time Dry cycle, then hold Start for two to five seconds.
- If nothing changes
- If the controls light up and all four checks pass, contact Whirlpool or schedule service.
Nothing lights up: check breakers, fuses and the power cord
- What to look for
- A tripped breaker or blown fuse, and how the power cord is connected to the dryer.
- What it indicates
- If neither the drum light nor the controls light up, the dryer has no power. Electric dryers use two household fuses or circuit breakers; gas dryers use one. On an electric dryer, an incorrectly installed power cord can also stop it starting or heating.
- What to do
- Make sure the fuses are intact and tight, or test the breaker by switching it off and back on. Replace a blown fuse or reset a tripped breaker. On an electric dryer, check that the power cord is installed as your installation instructions show (3-wire or 4-wire) and that the terminal screws at the dryer are tight — unplug the dryer before you check them.
- If nothing changes
- If the breaker or fuse problem continues, or you're not sure you have a 240-volt supply for an electric dryer, call an electrician. If the power supply checks out and the dryer still won't come on, contact Whirlpool or schedule service.
Brand-Specific Info
Error Codes
PF- Power failure: the drying cycle was interrupted by a loss of power. Touch and hold START to restart the cycle, or press POWER to clear the display. After a recent power outage, Whirlpool says to switch off the dryer's breaker for one minute, switch it back on, and watch the dryer for a minute to make sure the code doesn't return.
L2- Low or no line voltage, which keeps the heater from turning on (the dryer keeps running). Whirlpool says this only shows during initial installation. Check for a blown fuse or tripped breaker (electric dryers use two), confirm the power cord is installed correctly, then select a Timed Dry heated cycle and restart. If it persists, consult a qualified electrician.
F# E#- A code starting with F, alternating between F# and E#, means the dryer control has detected a problem that requires service.
Depending on the model, the start button is labeled Start, Push to Start or Hold to Start; all of them need a firm two-to-five-second hold. Touch panels respond to a fingertip, not a fingernail, and respond poorly when wet. Whirlpool also notes that pressing keys during the 10-second delay after power is restored can trigger a PF code, so give the dryer 10 seconds after power-up before touching the controls.
Some models have both an upper and a lower door latch, and both must be secure. The name of the no-start option varies: Wrinkle Shield on some models, Wrinkle Reduction on others. The Control Lock is turned off with a dedicated Control Lock button on some models and with the Cycle Signal button on most others. Electric dryers use two household fuses or breakers and need 240 volts; gas dryers use one.
What Not to Do
- Don't just tap Start and give up. Whirlpool says a tap may not allow enough time to engage the motor — hold it for two to five seconds.
- Don't press buttons straight after power comes back. Pressing keys during the 10-second power-up delay can trigger a PF code.
- Don't check or tighten the power cord's terminal screws with the dryer plugged in.
- Don't keep resetting a breaker that keeps tripping. Whirlpool says to call an electrician if the problem continues.
Frequently Asked Questions
Why won't my Whirlpool dryer start when I press Start?
Most often, the button was tapped rather than held. Whirlpool says Start, Push to Start or Hold to Start must be pressed and held for two to five seconds, because a tap may not allow enough time to engage the motor. If holding it doesn't work, check for a lit Control Lock light, an unlatched door, or a cycle knob set to Wrinkle Shield.
How do I turn off Control Lock on a Whirlpool dryer?
Hold the Control Lock button for three seconds. If your model has no separate Control Lock button, Whirlpool says holding the Cycle Signal button for three seconds turns it off on most models. Your owner's manual shows the exact button for your model.
What does PF mean on a Whirlpool dryer?
PF means a power failure interrupted the drying cycle. Touch and hold START to restart, or press POWER to clear the display. After a recent outage, switch off the dryer's breaker for one minute, switch it back on, and watch for a minute to make sure the code doesn't come back.
My Whirlpool dryer has no power at all. What should I check?
Check the household breakers or fuses first. Electric dryers use two, so make sure both fuses are intact and tight or reset the breaker; gas dryers use one. Then check that the power cord is installed correctly at the dryer, with the dryer unplugged. If the problem continues, call an electrician.
Will a Whirlpool dryer start on Wrinkle Shield?
No. On models with a cycle knob, Whirlpool says the dryer won't start if it's set to the Wrinkle Shield option (Wrinkle Reduction on some models). Set it to an Automatic Dry or Time Dry cycle and hold Start.
